How to wire a double switch to two separate lights

A double-switch allows you to operate two lights or appliances from the same location. Double switches , sometimes called double pole , allow you to separately control the power being sent to multiple places from the same switch. You can mount the switches side-by-side in a double -gang. Cut two lengths of black wire and two lengths of bare copper wire about inches long.

A wire that is bare, green, or yellow (or green with a yellow stripe) is the grounding wire , and the white wire is the neutral wire. In a double light switch setup, you will have multiple wires including one set each light fixture and one set that goes to the breaker box. There is only switch needed. Please see my diagram for details. In order to operate two separate lights , there should be at least one feed in the box and two traveller circuits (one for each light ). Turn off the breaker that powers the feed line in the wall box.

Included are arrangements for receptacles in one box, a switch and receptacle outlet in one box, and switches in the same box. Skill Level: Intermediate to Advanced – Best performed by a Licensed Electrician. Wiring a Double Switch or Triple Switch.

Tools Required: Basic Electricians Pouch Hand Tools and Voltage Tester. I am trying to hook up a double light switch to two separate lights but I cannot seem to get them to turn on. Here two switches are wired in the same box to control two separate lights. The source is at the switch box and a 2-conductor cable is run to each light.

One source is spliced to each switch with a pigtail to power the two lights. The photo that I share I got from lots of sources that can be truste so it is anticipated to assist you. Notice that the two switch combination device has the two screws on one side connected with a metal tab. Replace the wire between the switch and the light with 3- wire cable of the same size as is currently being used.

Connect neutral (white) of the hot cable to the neutral of the 3- wire cable. Have you got another switch for the ceiling light? This switch arrangement is basically two two way switches on a single face plate. A double gang light switch is designed to fit in a single-gang switch box, yet it offers the capability of controlling two separate circuits.

The switches are situated one on top of the other, and instead of the traditional switch plate, an outlet plate is used to finish the installation. Then at each light , I use a ~pigtail and each wire nut will house wires: source wire , pigtail wire to light , and the feed wire for the next light in that room? Back at the switch , for hot wire I will have source wire , pigtail to switch pigtail wire to switch , feed wire for room switch 1. We want to separate them by putting in a double switch. We have black wires connected to one side of the existing switch and a single red wire connected to the other side. How to Wire A Double Switch to Two Separate Lights Photos Free – Of the numerous images offered on the internet, there are several of the best images, we have that.

This will allow you to connect the first light as you described above, and to run this additional light from the same switch by utilizing the red conductor in the 3- wire as the “switched” conductor, and the black wire as the continuous hot wire. I want two seperate lights running from a double switch. Currently I have two lights that feed into a junction (the choc box), and from there into a single switch which works fine. Tighten all three screws to hold the wires to the combination two single pole light switch device. Push the device and the wires inside the gang box and attach it at the top and the bottom of the box with the screws provided with the device.

Three Wire Cable The Power Wire The Neutral Wire And The. One switch for the main bedroom lights and the other for the halogen. A double -pole three-way switch is able to integrate both of these functions into one. The switch cable from the halogens is only two core - brown and blue. The normal cable from the bedroom lights is two core (both red) and earth.

I want to add another switch , right next to the existing switch , in a double box to separately control the light and the vent fan. Wire the switch Loosen the screws on the new switch and wrap the wires around them the exact same way the old one was wired. If your setup does not include a grounding wire , make one by cutting a piece of wire and stripping it down to bare metal. Step - Wire in the Double Light Switch Connecting up a double switch light is essentially the same as connecting up a single switch light. Pick up the hot feed wire with some pliers and using your screwdriver join it to the hot connection on the double switch light.

Attach the new single-pole double switch to the electrical box. The cover connects with one screw to the centre of the switch. Cover the switch and the electrical box with a receptacle cover.

Turn the power on at the breaker panel. Turning off the switch simply disconnects the power wire from the light fixture, cutting off power from your lights. Start by taking your screwdriver and removing the two black wires attached to the light switch. Don’t worry about which black wire goes where. Lastly, remove the ground wire from the green screw.

Depending on the wiring arrangement at the switch you might only need to run one cable from the switch to your new light ( that is if there is a neutral present at the garage switch ). If not you will need to run a cable from your switch to yoyur new light and also a neutral from your garage light to your new light. The most common use of a double pole switch in lighting is the 4-way ( double pole double throw) switch. It is wired between two 3-way (single pole double throw) switches.

The other and less common use is a double pole single throw switch that can switch both phases to a 2volt light.