How to finish walnut

This finish gives walnut a dark yet warm color, and if you choose to apply it by wet-sanding, this too can fill the grain as above. I realy like the finish of walnut. A better quality brush translates into smoother finish application because a good brush holds more finish.

Oil finishes deepen the color of walnut. That’s a nice look and the oil adds protection, but it does nothing to warm the cool characteristics of the hardwoo especially the look of steamed walnut , which is grayish brown when freshly milled. What you have been doing is actually damaging the stock over time. If you have a satin finish on your stock, that gun oil is slowly eating that finish away. Stains provide no protection or gloss to bring out the figure of the walnut.

My prefered finishing technique for walnut is to apply two layers of Watco Danish oil natural color according to the manufacturers instructions, then after drying. For woods that have open cells, like oak or even walnut, which show up as tiny holes in the finish, you can use paste wood filler, which can be colored. Finish by spraying another coat of lacquer on the walnut just as you did the first time. Two coats are sufficient, but you can spray up to four coats for a deeper lacquer finish. I love to finish walnut with BLO.

Finishing a Black Walnut Kitchen Table - by. What is a good finish for Walnut ? If you plan on using a water-borne varnish or lacquer finish , consider warming up the walnut first with a coat of dye. A simple process of dying and staining walnut does several things: makes the color rich and vibrant, evens out or hides pale sapwoo and gives you color that will last a long time. Walnut has a reputation for being temperamental to finish , which is to say that to achieve long-lasting finish will require a little more work than simply applying a stain and polyurethane. Finish a piece of walnut with just clear and try one with the filler and see what you like best.

The grain filler can be tinted with a universal tinting color so I would recommend that. If you put the natural grain filler on walnut it will make white streaks in the grain. Apply your clear finish of choice. Dyeing walnut is not very difficult, but it will take some time. Brazilian walnut flooring is more durable compared to the standard black walnut flooring.

Applying finish to your walnut flooring will increase the lifespan of your walnut flooring as well as protect it from damaging elements such as water. It is also three times more durable than oak. Re: How to finish a walnut dining table? Synopsis: Black walnut has a lot going for it: It cuts and sands well, accepts stains without blotching, and often has attractive figure. But it can be frustrating to finish , because the creamy colored sapwood contrasts with the dark heartwood.

Commercial kiln-drying aims to fix the problem, but. We know how much you woodworkers love walnut for your projects! Brush on an oil finish , such as walnut oil, linseed oil or mineral oil. Allow the oil to penetrate overnight, and apply at least one more coat of oil afterward.

A water bourne finish is your lightest option. Sunlight will fade walnut a bit over time. You could do a test with some scraps and a diluted wood bleach. Butternut is in the walnut family and has a similar grain with a much lighter color. Would some tung oil and then a few coats of wipe on poly be good ? Hi Everyone, I just finishing up a Black Walnut Kitchen Table, and I could use your advice on applying a finish.

The appearance is only slightly different but different nevertheless. Kiln drying walnut can be done in a few different ways. Sometimes steam is added to the process either to prevent case hardening or to darken the color of the walnut ’s sapwood. Sadly, this can cause the walnut to go gray. In the photo above, a piece of steamed walnut sits next to a piece of solar-dried walnut.

I like to finish black walnut with a clear finish , and I think it looks especially good with a rubbed oil finish — like a natural Watco oil. If you run into walnut that has a grayish tint (I find this often in the cathedral grain of plainsawn walnut ), try sprucing it up with a bit of thinned cherry-colored oil stain. First, after the piece is nice and smooth from sanding it with 3sand paper, I apply some Danish oil and wet sand it to seal the pores.

I am interested in finding a quality professional finish to protect “my” walnut floor, and my reputation with the client. My question pertains to finishing the walnut. I like the idea of tung oil but I am wondering about a great sealer. Black walnut can look really “cold” with a water base finish and benefits from the amber tone that an oil base imparts. I have been trolling the forums for ideas.

Oak tends to have a more modern look with a water base finish and oil finishes will make it feel a little more classic. Same Day Shipping, 90-Day Guarantee Order Walnut Finishes Online Today!