Depends on how the light is wired. Check the outlet carefully. Does the switch control both parts of the outlet or only one part? The usual circuit is to control one half of the outlet while the other half is always hot. To accomplish this the jumper on the side of the.
How To Wire Up A Electrical Outlet To A Light Switch. Use your pliers and screwdriver to connect the hot black wire from the service panel to the top screw, and the black wire from the outlet to the bottom screw. To add an outlet to a light switch , you start by making a pigtail using the hot wire , the wire going to the fixture controlled by the switch and a third length of wire. You then splice all the white wires and all the ground wires in the switch box together. Hook up the outlet as you normally would.
A wire is then pig-tailed to the switch. Pig-tailing is a process where a short wire is cut to lead from a connector to a connection at a cap. Joining these two black wires is the black with from the outlet or receptacle. The red wire is connected to the opposite end of the switch box and to the black wire on the light (back in the light box). This wiring diagram illustrates adding wiring for a light switch to control an existing receptacle outlet.
The source is at the outlet and a switch loop is added to a new switch. The hot source wire is removed from the receptacle and spliced to the red wire running to the bottom terminal on the switch. From Douglas, a Homeowner from Hariman,Tennessee. Electrical Question: Is it possible to wire a switch for a light and at the same time connect an outlet to the switch that will not power off and on with the switch ? Wiring a Switch with an Outlet. Wrapping the wire clockwise when wiring a light switch ensures that the loop on the end of the wire will tend to close when the screw is tightened.
If you put the loop over the screw in the counterclockwise direction, tightening the screw will force the loop open and could create a loose connection. The problem is when the power comes to the switch , and then from the switch to the light outlet (or lights), and only on a 2- wire cable. In this case, you must change the cable from the switch to the light outlet from a 2- wire to a 3- wire cable. The exception here is if the outlet that’s controlled by the light switch is only connected to that light switch and there aren’t any other wires. If that’s the case, you’ll only have one black wire , one white wire , and a ground wire connected to the outlet.
A switch -controlled outlet is a great way to control lamps in the den, living room or bedroom. In fact, the National Electrical Code, or NEC, requires a switched outlet in a habitable room without. This diagram shows the wiring for a new outlet added from a light switch. Read about different wiring options, complete with pictorials and schematics.
How to Run Electrical Wire for an Outlet or Light Switch Running electrical wire behind a wall is a great way to add an additional outlet or light switch in your home. Switched outlets can be very useful when you want to coordinate lighting throughout the room to a single switch or dimmer on the wall. Hanging light fixtures with a pull chain switch can be connected to any available circuit, including a nearby wall outlet , provided that the light fixture will not overload the electrical circuit.
The closet ceiling light was wired in the prior installment. The new basement closet wiring has been roughed-in for the wall outlet power extension to the closet ceiling light. To determine how to wire an outlet and whether you can safely use existing electrical outlets , follow the list below. Wire a combination outlet switch for the convenience of having a switch and a receptacle in the same location. Many bathrooms have a light switch for overhead lighting, but no outlet for an electric razor or hair dryer.
Black wire is power, white is neutral and bare is ground. The receptacle has brass colored screws, and silver colored screws. The procedure for replacing a duplex (two- outlet ) wall receptacle is similar to that of replacing a switch. The only difference is that, depending on where the receptacle is located in the wiring scheme of your house, it may have more wires attached to it than you find attached to a light switch.
If you have more than one outlet , you need to find a way to get a neutral beyond the first one. See below - ground and boxes omitted for clarity (feed is from the left): If there is only one outlet between the feed and the switch , you just wire it like your top diagram with the outlet as the light. How to Wire an Attic Electrical Outlet and Light : A new junction box is wired for the switch controlled electrical outlet for the attic light after removing the old light switch and wiring. With alternate light switch wiring , an NM cable supplies line voltage from the electrical panel to a light fixture outlet box. This project is continued from the Exposed Work Cover junction box project.
Another NM cable connects from the light fixture box to the switch box. In the diagram below right, a 2- wire NM cable that connects the light fixture to the switch carries line wires (one line, and one switched line). The other terminal is for a second hot wire , called a switch leg, that runs only between the switch and the light fixture.
The ground screw is for the circuit ground wire connection. The switch leg brings power to the fixture when the switch is turned on. Attach the wire to any outlet convenient, and then carry on to the rest.
At the nearest outlet to the switch run a second drop to the switch. The white wire from the service panel is wired to one side of the light. That cable's white wire is also connected to the switch and runs back to and is connected to the light.
The black from the light goes to the opposite side of the switch. Flipping the switch interrupts the flow of electricity, and the switch does its job.
No comments:
Post a Comment
Note: Only a member of this blog may post a comment.