How to patch a hole in ceiling

Go to Home Depot in the drywall section they have drywall patches in different sizes. They go on very easy and the instructions are on the package. You don t need to put anything else behind it, but you will need a small bucket of drywall.

First take a knife or keyhole saw and cut the opening in to a. If it is drywall, easy and cheap way. Get a piece of cardboar bigger than the hole. Run string thur the center (dental floss works also) and back down about one inch over.

Get some drywall Spackle, spread around the inside of hole, push. Apply drywall compound around the hole with a putty knife. Use scissors to cut a piece of plastic mesh patching material to fit over the hole , sizing the patch to extend inch beyond the hole. Moisten a small, soft sponge and dampen the hole , rubbing gently. Press the patch into the hole and secure it to the wood cleats by driving drywall screws through the patch and into the cleat behind the hole.

Step - Fill in Joints and Screw Holes Spread a thin layer of drywall compound over the cracks between the patch and the ceiling with a utility knife. First, locate the existing framing that supported the old electrical box. Measure the depth and diameter of the existing hole to determine size of filler piece. Use a drywall saw to cut from inside the hole , out to each corner of the square.

Cut a bit past the pencil mark at each corner to be sure the new drywall patch will fit easily without forcing. Score the pencil lines around the hole with a sharp drywall knife. Screw backer boards above the unsupported drywall ends of the enlarged hole and install the new patch (Photo 2). Mist water over the surrounding ceiling texture in an area about in.

Then tape, mud and skim-coat the entire patch. Although you can attach a patch to a lathe , your patch will be better supported by screwing it to the joists rather than the lathes. Step - Cut Replacement Patch from Sheetrock.

From sheetrock , cut a patch the same measurements as the hole you knocked from the ceiling. Be aware of the thickness of your plaster ceiling when choosing sheetrock. Learn how to patch holes in drywall at This Old House. Use your jab saw to file away excess drywall until the hole is large enough. Replace any insulation you removed earlier, and fit the replacement piece into the hole in the ceiling.

Secure the drywall to the ceiling joists using drywall screws. The screws should just dimple the drywall rather than breaking all the way through the surface. Start the repair by trimming the opening in the ceiling into a square or rectangle, enlarging it as necessary with a drywall saw or utility knife. Holes in a plaster ceiling can be repaired and made undetectable in a matter of minutes.

For large holes and patch jobs, reinforce the hole with mesh or screen, but small holes simply can be. Get fair costs for your SPECIFIC project requirements. See typical tasks and time to repair a ceiling hole , along with per unit costs and material requirements.

Paint the patch to match the ceiling. After repairing a stain or hole in the ceiling , it may be necessary to repair the texture. Here’s how to do this: Using a putty knife, scrape off loose or damaged ceiling texture around the stain or repair. Place the patch over the hole and press the edges firmly into the wet compound. This will be large enough to look inside with a flashlight and handheld mirror.

Use the putty knife to apply a thin layer of compound over the entire patch. Another option for hiding that repair is a old scotch brite pad to scrub the points and edges. If you are repairing a recently painted ceiling and only want to blend it, use a light bit of paint and dry brush.

These step-by-step instructions demonstrate how to patch a ceiling hole where an old electrical box used to be. Patching a spot on a textured popcorn ceiling is not as difficult as you might imagine. Here’s how to go about it: Remove the hook from the ceiling and fill the hole with drywall joint compound.

Once the joint compound has drie apply popcorn ceiling repair spray (available to home centers) to. If you are not going to replace your old light fixture, cover the hole with a piece of drywall for a permanent fix. Use the same thickness of drywall as the surrounding ceiling , and cut the patch piece as close to the size of the hole as possible.

Let the patch dry and apply a coat of finishing plaster. It’s relatively easy to repair small holes in plaster if the lath backing that grips the plaster is intact. Place the self-adhesive mesh patch over the hole.

Repairing Holes in Plaster.