Cutting baseboards

Using a miter box or a power miter saw, cut the baseboard at a 45-degree angle. Before nailing it in place, mark the second piece the same way, and test for fitting. Installing baseboards is an easy do-it-yourself project, but cutting them can be tricky.

In this Article: Article Summary Removing Old Baseboard Trim Measuring and Cutting Baseboard Trim Installing the Baseboard and Finishing Up Community QA References. Baseboards cover the joints between the walls and the floor and add an essential finishing touch to a room. The cutting of baseboards isn’t a tricky process but you should take proper care while cutting it with a miter saw. For safety purpose always keep one side of the baseboard inside your miter box.

The user follows the pre-cut angles, cutting through the baseboard by hand with the backsaw. Miter-box saws are slow, but can cut correct angles in baseboard molding when no other means are available. When you rush you must know how to cut baseboards fast. It will save tonnes of your working time.

Making lots of corner inserts I had learned how to cut baseboards fast and easy. First hold the base molding against the wall after you cut it to length, and look for gaps. If you see some, cut a few braces from 4- to 6-in.

Tom Silva shows how to install baseboards that become visual anchors for any room. Measure and cut the baseboards for each wall. Boards that meet outside corners. A coping saw is used to cut baseboard for.

For larger or thicker baseboards , you can use a reciprocating saw to cut out a section, but this type of saw is more difficult to control, so you should be somewhat experienced in operating it. Place uncut baseboards firmly into the corner you are cutting for. One will be the baseboard you actually use, the other is just used as a guide. Take the piece that you already cut, and set it on top of the guiding baseboard firmly into the corner. With the guiding baseboard there, it should make sure that the board you already cut stays level.

Instructions For Cutting Baseboard Molding At Outside Corners Cutting Baseboard molding for a degree corner is a snap compared to the other corners. Just to clarify I will sometimes refer to baseboard trim or molding as base. One unfortunate side effect of cutting baseboards is the lip of melted plastic caused by the friction of the saw blade. Wait at least one minute after cutting.

By then, the plastic will be brittle enough that it easily snaps off. Coped joints for baseboard look great, but can be time-consuming. Instead of using a coping saw, learn to cope baseboard with a miter saw. It’s faster and works great for common baseboard profiles.

Visualizing a cut is therefore easier since this is the same orientation in which you will subsequently attach the baseboard to the wall. Roughly every foot, tape a spacer to the wall so it rests on top of the baseboard. I have a lot of fun cutting molding at my miter saw.

In fact, if you’re not having fun, something is probably wrong. Having a cutlist makes the job much easier. It’s also much easier if the baseboard you’re using is short enough to cut in-position at your saw.

Baseboards have miter cuts on outside corners and coping cuts on inside corners. Fit the longer runs first, that way any scraps can be used for shorter sections. Work from the inside corners out, installing wall to wall pieces first and saving those broken by doorways or outside corners until last. Shop our selection of Baseboard in the Building Materials Department at The Home Depot.

Re: Cutting Baseboards In Place When Installing when doing laminate, if i undercut existing bases, does the installation become harder vs qtr. Position the baseboard to cut off the face or profile if you are cutting an inside corner. Hold the baseboard tight against the fence with one hand. To mark baseboards and other moldings for cutting, make a jig called a “preacher”: Cut a slot the thickness of the molding in a scrap piece of wood. Put one end of the baseboard against the wall, and overlap the other end against the door casing.

If the baseboards meet directly at the ends, you need a square Joint. Use the miter saw set at degrees to make this cut. Use wood filler to seal holes and gaps.

Wait for it to dry and scrub excess filler with sandpaper. Always remember to allow the saw blade to come up to full speed before you start cutting. Angling the blade will create a point ensuring the baseboard face fits tightly against the adjacent piece. With a coping saw, cut along the profile.

Step 4: Sand for a Tight Fit. Sand the edge and try out the piece. How to Cut Baseboard Corners with Miter Saw ? One of the major functions of a miter saw is to cut baseboard corners.

The desire for every carpenter is to find the perfect formula for cutting perfect degree inside and outside corners. Add style and a finished look with decorative baseboards.