Thursday, June 15, 2017

Wipe on varnish

The answer is wiping varnish. It’s a versatile finish that is thin enough to wipe on, but dries hard even when applied in thicker coats. This allows me to build the finish quickly, then end with a thin coat. Wiping varnish is simply common oil-based varnish (any type, including alkyd varnish , polyurethane varnish or spar varnish ) that is thinned enough with mineral spirits (paint thinner) so it is easy to wipe on wood.


Wipe on varnish

However, it may require you to apply several coats before offering full protection for your furniture. Wiping varnish is simply any brand of oil-based alkyd (regular) varnish or oil-based polyurethane varnish in any sheen (gloss or satin) thinned about half with mineral spirits (paint thinner). Wipe On Varnish Techniques.


Leave all the excess (only on flat, horizontal surfaces). Allow to dry overnight or at least 6. A durable, clear finish that combines polyurethane protection with classic, hand-rubbed beauty. All with the convenience of a water-based finish. I have tried foam brushes to apply a wipe on varnish many times and just cant seem to get it right. With so many wipe -on finishes to choose from, you’ll probably find one you like right off the shelf.


But you can easily make your own. How to Get a Smooth Polyurethane Finish. Expert tips for applying a flawless clear finish. Wiping Varnish It doesn’t take a chemist to mix wiping varnish.


You’ll know exactly what you’re getting, and save a little money in the process. Applied with a cloth – no need to worry about drips and brush marks. Great for furniture, railings and trim. Place one of the T-shirt pads into the “do” bowl and let it soak up a supply of thinned varnish.


Wipe on varnish

A minute less on how to apply a simple, wipe on finish to wood. In a nutshell, the technique for applying a wiping varnish goes like this: You wipe on a full, wet coat, let it sit for a few minutes to tack up slightly, and then wipe off the excess. Since you’re leaving only a light coat on the surface, the varnish levels out very evenly.


You want to leave a thin, very even coat of finish on the piece. BARTLEY Gel Stains and Varnishes are now being produced by Seagrave coatings. They are identical to the original Bartley products and formulated to produce a professional looking finish with very little effort.


Durable clear finish combines polyurethane protection with classic hand-rubbed beauty. Just wipe on with a lint-free cloth — no need to worry about drips or brush marks. A great choice for any project, especially furniture, railings and trim.


I like to use an ol clean cotton T-shirt for this and the wipe -on step shown later. Remember to let the varnish dry between coats, and to sand and wipe the varnish clean before applying more varnish. Always work along the grain when applying and sanding the varnish.


When you get to the last coat, do not sand it. You also eliminate runs and sags when applying wipe -on finishes in thin coats. This is a heavily figured veneered top after about coats (over days). Question: TexJer I really like the look of some wipe on varnish I used on a small box.


Casy, adding oil changes the finish into a different and softer finish. You go from a wiping varnish to a Danish oil. What is the difference between wiping polyurethane and wiping varnish ? There can be no difference, they could be the same thing.


Although note that sometimes wiping polyurethane refers to the application metho not the product used. The range of finishes available to woodworkers offers a variety of positive attributes. I just purchased some wipe on poly, Minwax bran and naturally the directions say use a lint free rag.


By Larry Beyer in forum Project Finishing. You will get a better easy finish by skipping the poly then trying to add to it. Can you apply wipe -on poly over a varnished surface without stripping the varnish off? I have kitchen cabinets that were finished with varnish years ago and would like to put a more durable finish like Minwax wipe -on poly.


The problems with water-based wipe on poly are that chalk paint soaks it up like a sponge – so to get a clean smooth finish your going to want to dilute it with water. I use a 50: ratio for water and wipe on poly. Using a wiping varnish would speed up your finish process. Ron- The Arm-R-Seal is a wiping varnish itself. The key is the wiping , rubbing off the oil completely.


I have also read mixed reviews on water bourne wipe on finishes. We tested wiping varnishes, looking for the ones that are easy to apply and give great on a variety of woods. We tried them on both plain cherry and curly maple, evaluating the clarity, depth, and durability of the cured finish.


Thinning polyurethane to make a wipe -on.

No comments:

Post a Comment

Note: Only a member of this blog may post a comment.

Popular Posts