How to wire a fishfinder to a battery

Luckily, here you are, about to find out exactly how to wire your fishfinder to a battery and start your fishing adventure. You will need a couple of tools before you can start connecting it, so make sure that you’ve got your toolkit with you. Re: Help with wiring fish finder to my battery ! Your wires are probably 1 maybe ga. Radio shack has the smaller ones to.

Fishfinder direct to battery? What gauge of wire for fish finder. Same battery: Trolling motor and fish finder? After making sure the battery is switched off, connect the power leads, then plug the power and transducer wires into the back of the fishfinder. The manufacturer says not run a depthfinder on the same battery as your trolling motor.

Not sure why but it will void your warrenty. You can use 20- or 18-gauge wire and add alligator clips or small clamps on the en put an inline fuse holder on the positive lead within inches of the battery post and use a. How to easily wire and mount a fish finder to any kayak, UNDER minutes ! The battery in picture looks like it takes female spade connectors. Here’s some tips for making sure your fish finder technology is installed correctly and setup for success so you get the best performance possible. Find a goo sturdy spot to mount the main fish finder unit, while keeping in mind how accessible the unit will be for use. Drill starter holes to mount the bracket, then attach the bracket with the screwdriver.

Attach the fish finder to the mounting bracket. Check the bottom of this post for more detailed instructions on how to install a fishfinder for a kayak. Measure other end of wire from post to Lowrance power cable. The fish tape is stiff flat steel that is flexible enough to be pushed and pulled down the wiring channel under the gunnels of most boats.

Sounds like you removed the wire from the hot (red) terminal before removing the black terminal. It would also help to make sure the cable is disconnected from your fish finder before removing the individual wires from the terminals. Make a plan for all the wires to and from your depth finder. At a minimum, cover the wire with a cable cover strip. Hard Wiring Hds To Battery Sign in to follow this.

Re: Connecting Fish Finder to Battery Without a model number to go by, I would hazard a guess and say this thing has a memory of sorts and the third wire is a always hot line to keep from losing stored information when the unit is turned off. Things to Consider When Using a Fish Finder on a Kayak. First, you should start by positioning your fish finder on the kayak. Several of the options of the transducer mount I have mentioned above. The perfect position would depend on several factors, one of them the type of kayak you have.

It also has the battery loops on the end to connect to your battery. Most will wire into a dash switch or fuse panel. Where do the Blue Free shipping over $25. Free NEXT DAY shipping on select items. Fortunately, putting a fish finder in your pontoon isn’t rocket science.

It just takes time and basic electrical knowledge. How to Install a Fish Finder on a Pontoon Boat. With a little bit of help and some knowledge of your boat, you’ll be able to install a fish finder in minutes to a couple of hours. Install your entire fish finder with your transducer within a minute or less. Mounting the Battery Box: Cut a pool noodle in half (the width of the box) and using GOOP glue this to the back of the box (See photo O).

Let dry for hours with weight on top of the box (the battery works well for this). Place the box inside the front of the kayak. Hey guys, Im by no way a electrician but I know what the re black and white line is for and how to crimp lines. What I want to do though is have the ability to use quick connection for the red and black wires going from my 12v battery to the fishfinder and that is waterproof. Mounting a fishfinder permanently, or even semi-permanently, on a kayak is difficult at best.

While some of the most recent kayaks do include a mounting point, most do not. Additionally, most fishfinders require an external power source, usually a 12V battery – something that doesn’t exist on a kayak. Hummingbird power wire connected to rear battery with 1amp fuse inline and not tied to any other wire. The fuse will protect the equipment if power surges unexpectedly. Step 26: The last part of the process is to plug your wire into the back of the fish finder and fire up the unit.

Once it is on, everything is good to go. Step 27: Don’t forget to put your battery pack in a water-type battery bag. You can roll it inside the Kayak so that when water comes in, they won’t ruin the connection of your battery. Connect the BLACK wire from the trolling motor power cable to the negative (-) battery terminal of one battery ( battery B). Use a 40-amp circuit breaker on this connection.

So using our example of the 250mA fishfinder , it needs one quarter of an amp. Keep in mind that the longer your wiring run from the battery to switch panel is, the more voltage drop you’ll have (more about voltage drop). Prevent voltage drop by using larger cable. The power cables will be run to your New Wire Marine custom marine switch panel and your tinned marine negative bus bar.

You do need the appropriate amp fuse.