How to install a pocket door into an existing wall

Update an old pocket door by replacing it with a new one. The experts at the DIY Network give you simple step-by-step instructions. Did you ever have water come into garage under the garage door?

Clean off concrete floor and let dry, Snap a. This door functions similarly to a pocket door , but is attached to the outside of an interior wall instead of sliding into the wall. Steps to install a pocket door during new construction are slightly different, but should be easier. Install the door hardware and hang the door. Adjust for level and lock the adjustment nuts. If the wall is load-bearing , consult a structural engineer.

Remove the door and then install drywall over the door pocket , using construction adhesive and 1-inch drywall screws. Finish the joints with drywall tape and several coats of drywall compound. Reinstall the door and then install the door guides on the inside and outside of the door at the mouth of the pocket. Finish jambs go on the pocket side of the door opening, on either side of the door when it’s in its pocket.

Attach the split jambs with a pneumatic nail gun. With the old door remove you can cut a hole in the drywall next to the existing doorway for the pocket. The total space should be about twice as wide as the door. If the pocket is not deep enough, the door will not recess completely into the wall. Finally, install the door bumper on the stud at the back of the pocket.

However, any kind of door can be mounted on the proper pocket door hardware. I think it is about time for another half bathroom post. And today I thought I would tell you about how we install a pocket door. You can see below how the door opened up into the hall and it was just annoying.

And with kids it just always seemed to be open. Pocket doors can either be a single door or double door set up. The major downside to installing a pocket door is the need to have access to the framing around the door to create the pocket that the door slides into. In new construction and renovations, pocket doors are great, but replacing an existing door with a pocket door would mean opening up the walls around the door to install the pocket mechanism.

So, inspired by two sets of original pocket doors in our living room, we decided to turn our existing bathroom door into a pocket door. We were well aware of the problems associated with historic pocket door repair , because they are notorious for sticking, being noisy to operate, or worse, falling off of their tracks. Actual costs will depend on job size, conditions, size options.

To estimate costs for your project: 1. Set Project Zip Code Enter the Zip Code for the location where labor is hired and materials purchased. If you are wanting to install a pocket door in an existing wall you’ll have to remove some of those studs to create the rough opening for your pocket door kit. The quick answer to your first question is no. There is no easy way to install a pocket door in an existing wall without reconstructing the wall that contains the pocket. The cavity does have foam in it though.

The door slides between split jambs inside the wall. A bumper at the rear of the frame or the side of the door keeps the door from sliding too far into the wall , and guides at the floor keep the door from rattling inside the frame. For successful installation, there must be room for the pocket door to travel inside the wall. If you are cutting into an existing wall , lay out the opening so that the latch jamb of the door starts at the edge of an existing stud. Then lay out the rough dimensions and cut back to the stud closest to the end of the pocket frame.

A pocket door could work, but you would have to build a new wall inside the bathroom. Having a pocket door installed costs $400-$0(labor and materials) for a relatively straightforward installation in new construction or if the walls are already removed for a remodeling project, but can increase to $000-$5or more (particularly if walls must be torn open in an existing house), depending local rates, the materials chosen and the complexity of the project. This is done by creating a false stud wall along the side of your existing one with a space for the frame, the Rocket Pocket is only 100mm wide including plasterboard so you will not lose lots of space in the room.

The pocket door system can be installed against the existing wall. How to Convert a Hinged Door to Pocket or By-Pass Door ;. To install a pocket door you will have to modify the framing. Be careful when you cut into an old wall.

And yes, I have done several pocket doors. It will save him a few dollars. Typically, a pocket door is specified where a tight space makes it difficult to open the door inwards, or where a hinged door would impede access. In order to work, you need to plan ahead and to build an encasing wall wide enough to take the door. A standard internal door is just 35mm wide, so a 100mm-wide wall will comfortably wrap itself around a pocket door.

This page covers framing an existing wall to install a new door. Illustrations and instructions include: cutting into the wall , planning the frame, and installing a new king stud. To save time and make installation easier, you should use a pre-hung door for this project.