Ledger board flashing

Flashing your ledger board before installing your deck is crucial to ensuring your home and deck are protected from weathering. Learn how to properly flash a deck ledger board at Decks. Install the ledger board (I recommend using some spacers so the ledger is not ‘tight’ against the house).

Now install the Z flashing over the top of the ledger board , be sure the vertical leg is tucked BEHIND the Tyvek. Properly installing a ledger board for your deck is one of the most important structural components of building a safe and strong deck. These articles will teach you how to install flashing and bolt the ledger connection to the house rim. Then slip flashing behind the siding, covering the top edge of the ledger. Start by making an outline on the siding where you want to position the ledger board.

Make the outline large enough to include space for the deck boards on top, the ledger and any trim boards on the sides. During a driving rain, the ledger flashing is really put to the test. Given this, it makes sense to cut drainage notches on the underside of the decking board closest to the house. These notches will provide an easy way out for water trapped between the first decking board and the ledger flashing.

House wrap is cut up the house and the flashing is slid behind and stapled directly to sheathing. The wood deck ledger board flashing is replaced by tearing off the lap siding and installing new flashing to complete the deck rebuild. This project is continued from How to Replace Wood Deck Boards. Painted galvanized steel features a baked-on factory finish. Use asphalt paper between metal and pressure-treated lumber.

Installing a deck flashing properly is critical to keep water from getting behind the ledger board. The deck flashing needs to overlap the deck ledger board much like shingles overlap. Follow these tips when installing flashing on your deck.

Use the Amerimax deck ledger flashing to fit over deck ledger board and behind siding to protect from water damage. Visit the Home Depot to buy AMERIMAX HOME PRODUCTS INC. Ledger Board - Deck Attached: When a deck is attached to the house, a ledger board is bolted to the side of the house. To keep water out, metal flashing is carefully installed behind and on top of the ledger board (flashing is not shown).

Plastic Sheet Flashing Ratings. Protects deck ledger board from water damage. Make sure the flashing runs the entire length of the ledger board.

Once the ledger board flashing is in place behind the siding you can install the ledger board underneath. Afterwards you can use a wood block and a hammer to bend the flashing over the ledger board to form the drip edge. The ledger board attachment for this home was challenging because it was done after the house was constructed. So you will learn how the siding was removed and two layers of metal waterproof flashing were installed around the board. Install Z-style ledger flashing with a hemmed drip edge that extends over the face of the ledger and pushes water away.

Deck Ledger Board Flashing - Duration: 1:43. When it comes to flashing , the best choices are stainless steel and copper. DeckWise ledger tape can be applied to decking joists, around deck support posts and over ledger boards.

The flashing material at the top and bottom of the ledger board is improperly installed. Set the flashing in, Sliding the back up under. We installed 8″ Vycor flashing over the ledger and up the house side wall.

Corrosion-resistant flashing at the ledger is key to preventing water damage to the house. Everflashing is a Non-Returnable product. But many builders go further by isolating joist hangers from direct contact with pressure-treated lumber, and by flashing the tops of joists and built-up beams. But when you apply them over bolts, first add a stop bolt followed by a nylon washer, then the flashing , the ledger board , and another bolt finger tightened but not so tight as to prevent movement.

About a dime thickness off the face is good. It was necessary to tear off the bottom rows of siding to remove the old ledger flashing that was full of nail holes and install the new flashing. The HardiPlank siding is installe the joints caulked given a fresh coat of paint.

EVERFLASHING was designed and patented to help minimize water issues where the deck ledger board is attached. The IRC (International Residential Code) for more than years has stated that approved corrosion-resistive flashing must be used. Once the flashing is in place behind the siding you can install the ledger board underneath. LEDGER BOARDS: Twelve inch Deck Flash Barrier is recommended to provide ledger board protection. It should be installed with a minimum of inches of material up the wall of the building, and a minimum of inches of material down the face of the ledger board.

Some flexible- flashing manufacturers promote the use of these products at other locations, as well: to cover below-grade concrete cracks, at roof penetrations, under exterior door sills, over deck ledger boards, at inside and outside corners of wall sheathing, under stucco shelves and parapets, and over sections of wall sheathing susceptible to.