How to fish cable through walls

It really depends on the obstructions above and below. Is your roof real shallow where you would have to put a drill? If your box is closer to the groun I would come from below if possible.

Cut the hole in the wall where you want the outlet box. Drill a hole through the header above the box in the attic, it may be easier to drill the hole from the room up and patch the hole than to drill from above. Drop a line with a weight. Pull the cable through with a fish tape. Carefully extend the fish tape from one opening to the other.

Tape the end of the fish tape tightly onto the cable with electrical tape. Make sure the tape is smooth so the cable is able to slide through the opening. Then, retract the fish tape to pull the cable through.

If you’re running cable through a basement or crawlspace, drill a hole in the bottom plate directly below the box. Feed your fish tape into the wall opening, pushing it up into the hole you made in the top plate. Fish tape is a springy steel tape that electricians use to pull wire through walls. Fish tapes are the best tool you can find for pushing through holes in a wall.

Install a wire or fish tape through the hole in the floor and let it dangle through the hole. The potential is always there to damage the vapor barrier or bunch up insulation, leaving cold spots in the wall. If you must fish wires through exterior walls , the best tip is to avoid spinning the flex bit until you make solid contact with the wood you plan to drill through. Learn how to fish cables through walls. WiFis Monoprice cable fishing video tutorial using our mounting.

Fishing the wires through walls. Now you should be ready to fish the wire. From the basement or attic, push the wire fish tape through the hole you have drilled.

Have someone at the other end reach through the hole in the drywall, grab the fish tape and pull it through with about a foot sticking out of the hole. We will have to repeat these steps for any ceiling area that needs to have cable run across the joists. When we need to run with the joists, we can just cut one hole at the start, then one at the end and use our fish tape to run through the ceiling. If you’re working from the attic, you can drop a weighted string down wall cavity, then attach the wire to the string and pull it through. Run the wire or cable to its destination.

Electricians use a tool called a fish tape. After you successfully get the fish tape through to the remote en you attach the wire onto it and pull it back through. This may be easier said than done, and it’s good to have a helper. In my experience, the “ wire fish ” tool is necessary… we tried a wire clothes-hanger, and it wouldn’t work.

Drilling up or down and fishing cable through insulated walls is an inconvenience, but nothing more. Sure, there are certain techniques you can’t use through insulation, but there are always work-arounds. During sweltering Florida summers, temperatures in these spaces can climb to well over 130°F. Push the fish stick up through the tube and out of the top low voltage box. Extend the fish stick so that it protrudes out of both the top and bottom holes and you can tape it to the wall temporarily.

How to Fish Wire Through a Ceiling. When you are doing your own remodeling or electrical repairs, you can sometimes find yourself in difficult situations. Col cobweb-filled crawl spaces, damp basements and tight attics are all just a part of the job.

Tools needed for running wires:. Is there a way to still get the cable through. Attach the cable to fish tape. Hello, I spent a good hours today trying to fish a cable down a wall that had insulation inbetween the studs. It was very frustrating because the cable , fish wire, would bunch up and get stuck.

The most annoying part is the cable keeps feeding into the wall so there was a lot of let downs when it was not at the bottom. If you’re fishing a small cable (like a security cable ), you can attach the cable to the end of the rod by threading one of the wires in the cable through the hole in the bull-nose. If you need to fish a larger cable or bundle (or if your buddy is going to feed the cable to you from above or below), thread a pull-cord through the bull-nose. The idea is to drop this magnet behind the wall , and use a second magnet to fish it through to where the cable needs to go.

Whether sticking the magnet into the wall from above in the attic, or from below in the basement, the idea is the same. Snake fish tape, a piece of thin steel wire designed to guide and retrieve wiring, through the light fixture hole in the ceiling toward the wall -to-ceiling access hole. It can get difficult to maneuver the more you use.

It also gets a little more difficult to reel back in. If we hit any snags, we’ll use this fish tape to help pull the cable or conduit on through. Now we’ll head across the wall , first with our electrical cable , then with the plastic conduit. We’ve got our wiring run and in place. Anyone have any helpful pointers about fishing electrical wire through plaster and lath walls ? My friend wants to install a ceiling fan.

I know how to repair the plaster for the holes once I am done, but I have already assumed the project will be a headache, since I know old plaster walls can be difficult. My cable TV is distributed through the attic, so it seemed like a good solution to run my home network through there as well. Strong string or a fish tape.

I am trying to figure out if there is an easy way I can fish the cables through , or even better, fish some sort of conduit.