Thursday, April 25, 2019

How to install outdoor electrical outlet in yard

If you don’t have an outdoor box to tap in to, consider installing one on your house. You can expand the project to include additional outlets , switches and lights. The techniques for running the wire and mounting electrical boxes are the same.


Turn off the power to the existing outdoor outlet. Using the screwdriver , remove the screws holding the cover and set the cover aside. Remove the top and bottom screws on the outlet and pull the outlet out of the box as far as you can while leaving the wiring intact. Install an outlet on the exterior of your house so that you can more easily light your yard and power your tools.


Outdoor outlets have watertight covers that allow them to stay covered even with a cord plugged in. The National Electrical Code requires the use of ground fault circuit interrupter (GFCI) outlets outdoors. It came with a standard three-prong outlet , but since outside outlets must be GFCI protecte we replaced the kit outlet with a GFCI outlet. Make the wire connections between the cable and a GFCI outlet.


Screw the outlet to the box, then apply a bead of silicone around the face of the box. From inside the garage , install a cable connector onto the main electrical box. Pass the cable end through the connector, then tighten the connector. Installing wiring for an outdoor outlet should be done according to local and national electrical codes with a permit and be inspected.


Methods for Installing an Outdoor Outlet. First Lets Review Some Very Important Electrical Code Considerations. An electrical outlet may not be installed within feet of the inside wall of the pool.


How to install outdoor electrical outlet in yard

The drawback to these tools is that they must be plugged into an electrical outlet in order to function, which can be an issue if you have an extremely large yard. Thread a piece of exterior-grade electrical cable from the interior electrical box through the hole in the exterior wall. Be sure the cable is long enough to reach from the interior to the exterior box. Inside the house, pull back the insulation sheeting from the electrical cable.


Tools for Installing an Outdoor Electrical Outlet : - hammer-drill fitted with carbide-tipped masonry bit, for boring through concrete and brick - impact drive - pliers - screwdriver - caulk gun. Attach the ground wires together with a barrel crimp. This is generally against code and would not be safe for you or the circuit. The outlet would need to be outdoor rated as well as ground-fault (GFCI) protected.


I have an outdoor breaker panel that supplies 2power to my pool pump. I would like to install a 110v outlet to power hand tools,leaf blowers etc. You stretch what seems like miles of extension cord around your house to weed whack, plug in Christmas lights, or just listen to some tunes while enjoying your yard. Next, re- install the outdoor electrical outlet into the electrical box, replace the faceplate, and turn the power on at the service panel.


Test to see if power is running to the outlet. If you have power in the outlet the capped wires are the LOAD wires. To remove the electrical box from the wall, remove the mounting screws. Pull the box out and pull it off to the side.


How to install outdoor electrical outlet in yard

Push through a knockout space in the box for the new wiring. How to Install Outdoor Electric Wiring. Get electrical help with help from one of the one of the owners of CJS Electric in Tampa Florida in this free video series. Set the low-voltage electrical cable in the trench.


Leave a bit of slacked cable at each fixture point for making the connection to the light fixtures. Smooth the soil over the trench, but leave the cable sticking up out of the soil near each fixture. Expect to spend about hours installing a new outdoor receptacle with an extension ring and in -use cover. Add-On Lamp Post Outlet, Black. Installing Lamp Post Outdoor Electrical Outlet Saves Significant Installation Cost Compared To A Stand Alone Outdoor Outlet.


How to install outdoor electrical outlet in yard

Loosen and remove the screws and cover plate over the existing outlet , using the screwdriver. Remove the screws holding the outlet in the junction box and pull it out, but leave the wiring attached. Remove one of the expansion plugs on the side of the box, which allows conduit to be connected to the box.


How To Install Outdoor Electrical Outlet In Yard. A well-lighted yard also deters crime. The range of outdoor lighting options runs from motion-sensing floodlights, to sodium-vapor yardlights, to low.


Outlet location: If your outdoor outlet is installed in an area with existing wiring or access to an electrical box, it takes less time to install and reduces labor costs significantly. Of course, the opposite is also true. Years ago, I wanted to install an outlet on a lamp post near the driveway. Rather than trying to find a GFCI outlet to put in the pole, one was installed in the house and the wiring run off of load side of the outlet in the house to the lamp post outlet. DO NOT do this, its not done correctly.


Do it safely and easily with this simple through-the-wall technique.

No comments:

Post a Comment

Note: Only a member of this blog may post a comment.