Electric fence ground rod

The fence charger, or energizer, is designed to alter the electric charge into a power that is safe for animals and people. FREE Shipping on eligible orders. For installations with bare wire, use a stainless steel ground rod clamp to secure insulated wire to the rod.

Most battery and solar fence energizers include a wiring harness for easy connections. Do not use copper ground rods as these will lower the effectiveness of the connection. If the power is not sufficient, you may need to add another grounding rod to your electric fence grounding system. Most fences will require two or three grounding rods positioned about ft. The “ ground system” is a series of highly conductive rods driven into the soil and then connected by wire to the ground terminal of your fence energizer.

The ground system collects electrons from the soil to complete the circuit needed for delivering an effective shock to your animals. Inadequate grounding is the most common failure in electric fence operation. Consider that the grounding system of an electric fence is similar to the antennae on a television set, the larger the antennae, the greater the reception. The grounding rod for electric fence wire should be around feet long.

This creates a grounding system for your electric fence. How to drive in a ground rod , and connect it to the negative terminal of your charger. The electric fence ground rod kit promotes proper grounding of electric horse fence chargers. If your electric fence charger isn’t grounded properly, your horse containment fence will be compromised and your horses could run free or escape.

Larger energizers with large fence lines require more ground rods. For an electric fence to give an electric shock the current produced by an energizer must complete a full circuit. A general rule is to install a minimum of feet of ground rod per joule of output capacity.

Grounding the electric fence. When an animal comes in contact with an electrically charged fence , the animal. Save electric fence ground rod to get e-mail alerts and updates on your eBay Feed. Drive it into ground directly below the charger, or at the closest point where ground access is available.

Electric fence ground rods are connected to the charger. Some folks run a ground wire strung on the same posts as the hot wire. You know that an electric fence is a great way to protect your property, and to keep your livestock safe and. The T-Handle also makes it easier to move in temporary fencing applications or insert in hard ground conditions.

Never use an existing grounding rod that is connected to another electrical device or use a water line to ground your electric fence. Testing your electrical current The performance of your fence charger’s ability to keep your cows, cattle and other livestock safe and contained relies on the effectiveness of your ground system. Use enough ground rod (s)—included with our energizer kits. Don’t allow your lead acid battery to discharge below.

Use insulated wire that is designed for electric fences. Always connect the fence to an energizer, not an outlet. Visit this link for to other common energizer questions. We should be generous when it comes to the grounding system for our fence project. Installing at least galvanized ground rods 5’ deep, 10’ apart creates and adequate ground bed for most small energizers.

One grounding rod will need to be installed within feet of the electric fence controller. An internal fault on an improperly grounded fence controller could result in a risk of high electric shock currents on the electrified fence. This is not enough to properly support the electric fence. Use the proper type of grounding rod. In most cases, pipe or rebar can be used.

When an electric fence is installed right, the shock it delivers is very effective in keeping predators out and livestock in. But, if the fence isn’t properly grounde the electrical circuit isn’t complete and will be useless. Improving the grounding is a low-cost, effective way to improve the.

I have an electric fence now, but only one ground rod , which I think is causing the fence to not be grounded well enough. How do I add more ground rods ? I have the rods and the clamps, but the first rod is connected with a vinyl covered wire. Do this along the fence line at a point near the electric fence charger by pounding the rod into the ground until only a few inches are sticking out. A ground rod insures that when something hits that fence , it will feel it! Poor ground could cause stray voltage if fencer ground.

DO install first ground rod within feet of charger. DO use ground clamp to attach ground wire to ground rods. A sample ground clamp is furnished with your fence charger (110V A.C. models only).