Tuesday, October 20, 2015

Stain over polyurethane

Stain over polyurethane

Think of gel stain as a type of opaque paint. If you really want to change the color without stripping, gel stain can do it. Polyurethane stain blends are available in the most-common wood stain colors.


It can also be used over polyurethane finishes, so you can change the color of your finished woo without removing the existing finish. However, some polyurethane -blend stains are designed to be used over a polyurethane finish. If you want to touch up furniture with a polyurethane finish without completely refinishing the piece, you can use a polyurethane stain blend like those sold on Minwax. I think one misconception is that you have to strip and sand a piece down to bare wood before you can re- stain it.


Sometimes that is necessary, but if you have a piece without much of a topcoat (sealer, poly , etc) and the finish is in good shape, you can go over it with a gel stain. Minwax Polycrylic is an example of a fortified water-based polyurethane than can stand up a bit better to rough conditions. It also can go over oil-based finishes and can be applied using synthetic-bristle brushes, a foam roller or a rag, as can other water-based polyurethanes.


Stain over polyurethane

How to Use Oil Base Gel Stain Over Existing Finishes. General Finishes HP Poly and. Learn how to put polyurethane over stain on your wood furniture.


A stain is typically applied one coat at a time, but subsequent coats penetrate less and less as the pores in the wood become saturated with stain. Re: Can you stain over polyurethane ? Or you can stain and then poly. Just finished putting two coats of oil based polyurethane on a red oak entertainment center that was stained with Minwax gel stain.


SWMBO noticed that the lower section of the entertainment center is lighter in color than the top. Staining over stain is easy and works beautifully if your applying a dark stain over a lighter stain on raw wood. You can mix or more stains together to make DIY custom stains.


Warm stains work great to slightly warm up cooler toned stains. Pick an inconspicuous spot to test your stains before applying to the entire surface. Can I apply water-based polyurethane over an oil based stain ? This is because the curing process for oil is polymerisation, and polymerised oil is akin to resin.


If you try to finish over it with a brush, some of the stain will probably come off on the brush and give the surface an uneven look. You could spray several light coats of finish over the stain , but the adhesion between the finish , stain , and wood will not be very high. Painting over polyurethane requires patience, time, and effort. You’ll have to prime, sand and use oil-based paint in order for your paint to stick to the finish of your wooden furniture.


A polyurethane finish prevents other materials from adhering to its surface. Wood furniture often comes with a polyurethane varnish or lacquer that prevents an easy or immediate decor change. But with careful preparations, you can paint over finished wood in your home and. One key to a good polyurethane finish is a smooth surface, because your finish will only be as smooth as your wood Sand your project with progressively finer grits of sandpaper. Paper with a higher grit number removes the deeper scratches left by paper with a lower numbered grit.


How to refinish and restore a polyurethane floor without stripping the old finish. This one-step stain and finish product transforms furniture without the need for stripping the old finish. Whether it is oil-based or water-base it comes in a variety of finishes, from glossy to matte. Will my finishing solvents go bad over time?


For more related content, subscribe to our newsletter! Both products provide a clear, durable finish but in my opinion oil-based poly has an advantage over water-based poly. Oil-based polyurethane gives DIY furniture an additional depth of color that you just don’t get with water-based poly. If you used an oil-based stain on your project I would use an oil-based poly.


Once hardene it forms a strong protective shell over wood. Moreover you cannot dispute the shine that polyurethane layering gives to expensive wood furniture and wooden flooring. I did my best on one rolling tool chest that has a “grand piano” finish of polyurethane over epoxy for a number of years now and. Selecting a deck stain or sealer is a vital step when finishing your deck or when your deck is in need of being recoated. Wood decks are exposed to severe weather conditions and need to be protected with the correct type of wood sealant.


Click the link below and get directions to your closest Sherwin-Williams store. Applying a clear sealer or polyurethane over a deck stain will cause more problems than it is worth. If you want a clear finish then you can strip off any old stain and start fresh with bare wood. Then you can apply a clear sealer if that is the look you are going for. Oil and water are famous for repelling one another and not mixing.


Luckily, there are ways around this when it comes to applying finishes. Coating wood cabinetry, furniture, or trim with a clear finish , whether you stain it or not, gives it richness and depth while protecting it from knocks, scrapes, and the weather. Use this guide to learn more about choosing and using polyurethane , the toughest of the clear coatings.


Self-leveling formula provides superior scuff scratch and stain resistance. Premium polyurethane floor coating continues to deepen its amber look over time giving wood floors a. Enduro Clear Poly Water Based Topcoats and Sanding Sealers. All stains need a top coat.


Because MDF is not as absorbent as natural woo let the piece dry for a couple of days in-between coats and before applying top coat. For top coats, we recommend water base High Performance if you want a clear coat with quick dry time or Arm-R-Seal oil based polyurethane if you want more ambering. Had a custom breakfast table made, which took forever ( over a year) to receive, and I have multiple wax coats on the top but am noticing every scratch, fingerprint, etc.


Thinking about buffing the wax myself then applying a wipe-on oil based poly. The table is a dark stain.

No comments:

Post a Comment

Note: Only a member of this blog may post a comment.