Hei distributor wiring

Well pretty much what the title says haha! Its really hard to do videos off the top of your head and it really shows in this one. I for get what electrical tape is called haha. FREE Shipping on eligible orders. Connect that wire from the ignition switch directly to the BAT position on the HEI.

GM HEI electronic distributor is wired up thanks for watching and please subscribe. View search for HEI wiring and get Free Shipping on Orders Over $at Summit Racing! See and discover other items: wire harness connectors, hei distributor , gm pigtail connectors, distributor to coil wire , hei parts, chevy wiring connector Set up an Amazon Giveaway Amazon Giveaway allows you to run promotional giveaways in order to create buzz, reward your audience, and attract new followers and customers.

The second concerns the gauge of wire feeding the HEI distributor. The third concerns the starter volt override and the ignition switch. When using HEI , the distributor requires a volt feed.

In order to achieve this the ballast resistor or the resistance wire must be removed from the circuit and replaced with a pure gauge feed wire. No resistance is used in an HEI application. Modified diagram for trucks with HEI ignition and internal regulator alternator with factory gauges. Fill Your Cart With Color Today!

Whatever you are, we try to bring the content that matches what you are seeking. HEI Distributor Installation Instructions DISTRIBUTOR REMOVAL 1. Remove the distributor cap, leaving the spark plug wires attached. Disconnect the vehicle wiring harness, and distributor wiring harness from the distributor cap.

Set the cap and wires out of the way. Connect the primary wires to the HEI distributor , via a plug that snaps into the distributor cap. There are two wires in the plug: the hot wire and the tachometer wire. If you are updating from an old distributor , splice the old distributor hot wire to the hot wire of the HEI primary plug.

Powering them through the original wiring will mean that the Ballast Resistance will still be present. I do agree with using the gauge wire , and if the original poster ever finds the correct wire , he should install a new gauge wire from the ignition switch to the new distributor. I just got my new HEI distributor from Jegs. I have a few questions with the connections.

So on that distributor there was only a black wire coming out of it. On the old coil, there was the black from the distributor base. Upgrading a Points Distributor to an HEI System Technically Speaking.

Note: HEI type sets do not include remote coil wire. The integrated coil keeps underhood wiring clean, and for race cars, the idea of running one wire to the distributor keeps things simple. The HEI ignition requires a switched (turns on and off by a switch) 12V DC power supply (without any resistance from a ballast resistor or a resistor wire like was used on many GM points-type ignition systems), and a ground.

Ignition Module, 4-Pin, GM, Stock HEI , Each. Distributor Wiring Pigtail: This wiring pigtail features a dual HEI connector that helps clean up your engine bay by eliminating the use of single spade connectors to make battery and tachometer connections. Find Distributor Wiring Harnesses and get Free Shipping on Orders Over $at Summit Racing!

Then take the other wire from the old coil - remove the ballast and run it straight to the HEI 12v in. The wire from the distributor goes to the - termi-nal on the coil. There may be an additional capacitor on the coil - terminal.

This is to eliminate radio interference. The old distributor can then be removed from the engine. The HEI is a complete distributor that uses a large distributor cap with male terminals.

It has a built in ignition module and ignition coil. No external modules or wire harnesses to deal with. Gm Hei Distributor Wiring Diagram – Wiring Diagrams, size: 8x 6px, source: duxse. GM Single Wire Coolant Temperature Sender Connector $6. Our HEI distributor wiring kit makes it easy to get the wiring correct, and proper wiring is critical to maximum spark output from the HEI system.

The HEI ( H igh E nergy I gnition ) system is at its best when operating with 14volts input. This distributor works exactly as advertise it is a nice package and looks beautiful! I did some additional research and learned that you must combine the yellow starter solenoid wire with the new gauge wire to power up the HEI distributor. The car started first time without any issues by wiring it this way. I called Sun to check on correct wiring they said that I only had to move tach signal ( think that it was green) from neg side of coil to tach plug on the GM HEI.

The distributor is the mechanism that sends voltage from the ignition coil to the spark plug. HEI Kit Installation Instructions The two wires with the white connector for the ECU go to your two distributor connection wires. Wire connectors can be used if need be. If you have a connector from and old distributor you could use that would be fine. Don’t seal up those wires permanently just yet.

When disconnecting the battery cables, always remove the Negative (-) cable first and install it last. This also eliminates the possibility of bleed-through from one wire to the other. And by using quality materials.

The vehicle never had an HEI distributor in it.